|
| |
|
AppBee's - Adapter boards for
MaxStream's ZigBee RF XBee's
Now shipping bare
PCB's for you to populate! Parts
Kits / Assembly Testing now available through the Order Page
$7.95 per board for parts (XBee NOT included)
$5.00 per board for assembly.
100mW XBee-PRO
Order
from
www.digikey.com
- Search for XBee
or www.maxstream.net
1mW XBee
Order
from
www.digikey.com
- Search for XBee
or www.maxstream.net
|
The XBee, from MaxStream, is a wireless transceiver (modem)
using the IEEE 802.15.4 Low-Rate Wireless Personal Area Network
protocol (LR-WPAN) for Wireless Sensor Networks (WSN).
This allows addressable communications between nodes. Data may be sent to individual nodes (point-to-point), or to
all nodes in range (point-to-multipoint) using a broadcast address.
The devices use clear channel assessment (CCA) on a CSMA/CA
network which helps ensure devices do not talk-over one another.
In point-to-point communications, error checking,
acknowledgements and retries are used to ensure data delivery.
The use of flow control (RTS) helps ensure devices, such as
the BASIC Stamp, do not miss incoming data. These devices are great in wireless sensor & control
networks, robotics and for teaching networking! Use the BASIC
Stamp or other microcontrollers, such as the SX, Propeller Chip,
Javelin, AVRs, PICs, etc, for networking devices.
Using the BASIC Stamp, code to send data is as simple as:
SEROUT TXpin, 84, [DEC x,CR]
And to accept a byte of data:
SERIN RXpin, 84, [DEC x]
Optionally, the device may be configured to use flow
control so the data is buffered, then the BASIC Stamp may use:
SERIN RXpin/RTSpin, 84, [DEC x]
|
XBee Features
|
|
XBee
|
XBee-PRO
|
|
* Range - Indoor
|
100 ft
(30m)
|
300 ft
(100m)
|
|
* Range – Outdoor
|
300 ft
(100m)
|
1 mile
(1500m)
|
|
Transmit Power
|
0 dBm
(1mW)
|
20 dBm
(100mW)
|
|
Receiver Sensitivity
|
-92
dBm
|
-100
dBm
|
|
TX Current
|
45mA
|
214mA
|
|
RX Current
|
50mA
|
55mA
|
|
Power-Down (Sleep) Current
|
<10uA
|
<10uA
|
* Ranges are line of sight and height dependent.
 | IEEE
802.15.4 compliant, Low-Rate Personal Area Networking. |
| 2.4
GHz DSSS (Direct Sequence Spread Spectrum). |
| 250,000
bits per second. |
| Acknowledgement
and reties. |
| Addressable,
> 65,000 addresses available. |
| Point-to-Point
and Point-to-Multipoint (broadcast) messaging. |
| Channel
and Network ID selectable for cluster separation. |
| Fully
configurable via serial commands. |
| Transparent
transmission and reception |
| Flow
Control using RTS/CTS. |
| Receiver Signal Strength Indication (RSSI). |
| Free X-CTU interface software. |
Network
Communication Illustrations
Any node can talk to any other. Lines illustrate some examples.
All
boards are currently sold as unpopulated (bare) PCB's.
You must add your own parts.
AppBee-MOD
Order Bare PCB
$5 each
Parts List
Parts and Assembly available
through order page.
|
AppBee-Mod (5-12V) is an application interface board
that connects to the AppMod dual row 20-pin header of many Parallax BASIC
Stamp boards for power and quick communications to the BASIC Stamp.
This board has connections to many I/O features of the XBee to
provide greater flexibility.
- On-Board
3.3V regulator and 5V conditioning.
- Supplied
power range from 5V to 12V
- Transmit and Receive LEDs
- Communications with PC directly using the Parallax USB2SER
- 10
Pin header for jumpers to P0-P15 and 20 Pin AppMod Header
- TX,
RX
- XBee
Reset
- RTS
and CTS for flow control
- Receiver
Signal Strength Indicator output (RSSI)
- Association
Indicator I/O output from XBee (ASSOC)
- Sleep
Indicator I/O output from XBee (SLP_I)
- Sleep
Request Input to XBee (SLP_R)
- XBee Header allows direct connection to all available
XBee I/O if desired.
- Signal
conditioning may be required for direct connection to the XBee.
- Accepts
the USB2SER to have your PC on the network or use the USB Base
Station.
|
AppBee-SIP
Order Bare PCB
$4 Each
Parts
List
Parts and Assembly
available
through order page. |
AppBee-SIP (5-12V) is an application interface board
with a 6-pin single row header for easy connection to breadboard and
custom printed circuit boards. This
board has only essential connection for power, communications and
accessing sleep modes of the XBee, though additional jumpers and circuitry
may be used to expand on the provided I/O.
- On-Board
3.3V regulator and 5V conditioning.
- Supplied
power range from 5V to 12V
- Use with 3.3V or 5V signals
- Transmit and Receive LEDs
- Communications with PC directly using the Parallax PropPlug
- 6
Pin header for power and I/O for breadboard mounting.
- TX,
RX
- RTS
input to XBee for flow control
- SLP
input to XBee for sleep request
- Additional
4-pin header for the
PropPlug to have your PC on the network or use the USB
Base
Station.
- XBee Header allows direct connection to all available
XBee I/O if desired. Signal
conditioning may be required for direct connection to the XBee.
|
AppBee-SIP-LV
Order Bare PCB
Parts
List
Parts and Assembly available
through order page.
|
AppBee-SIP-LV (2.8V-3.4V) is an application interface board
with a 6-pin single row header for easy connection to breadboard and
custom printed circuit boards. This
board has only essential connection for power, communications and
accessing sleep modes of the XBee, though additional jumpers and circuitry
may be used to expand on the provided I/O. This is designed for
boards running at 3.3V or in that range. Do NOT use with 5V devices.
- Supplied voltage range from 2.8V to 3.4V
- Transmit and Receive LEDs
- 6
Pin header for power and I/O for breadboard mounting.
- TX,
RX
- RTS
input to XBee for flow control
- SLP
input to XBee for sleep request
- XBee Header allows direct connection to all available
XBee I/O if desired.
- PropPlug and USB2SER from Parallax may be used for direct PC
communications via
your breadboard.
Note: Documentation not yet updated
for this board.
|
AppBee-Proto
Mounted with standard pin male and
10-pin PCB header
Order Bare PCB
Parts
List (same as SIP_LV)
Parts and Assembly available
through order page.
|
AppBee-Proto (2.8-3.4V)
- Supplied voltage range from 2.8 to 3.4V.
- Pinned for the Propeller Proto Board headers.
- Hardwired connections for TX, RX, Vdd and Vss.
- Jumper holes for other XBee I/O.
- Ships with: Red and Green LED, 2mm XBee headers, 2-100 ohm
resistors,
10uF cap, 10-pin right angle male.
- Use the supplied header or use an AppMod or other 0.1" header.
The board has a 2-row
0.1" solder holes for 20-pin headers.
-
PropPlug and USB2SER from Parallax may be used for direct PC
communications via
your breadboard/solder board.
Note:
Documentation not yet updated for this board. |
 |
For
PC's we recommend Maxstream's USB board for data
communications and updating the firmware if need be. We no
longer sell the single-board XBee dongle - sorry.
The
USB board can be purchased from DigiKey
- XBIB-U-ND, $60 USD.
|
|
Documentation:
|
|
Code Examples:
|
|
Resource Links:
|
XBee and XBee-PRO are
registered trademarks of MaxStream, Inc.
BASIC Stamp and USB2SER are trademarks of Parallax, Inc.
|
|
Contact
us
